L117 Offset Pivot Set

L117 Offset Pivot Set

$726.98

  • Return period: 60 days
    • $
    • $
    • $
    • $
    • $
    • $
    • $
    • $
SKU: L117 Category:
  • Description

Description

L117 Offset Pivot Set
For Doors Up To 1750 Lbs.
Ships With L180 Top Pivot
NOTE: Ships standard for 1-3/4” thick doors. May be specially ordered for thicker doors.

Product Description & Features
• Standard top pivot L180 included
• ML19 intermediate pivot required (order separately)
• Bottom pivot mortised into floor
• Available for fire door assemblies up to three hours (ferrous material). Specify FL117. Intermediate pivot required by UL. Specify FML19 (order separately). Note: UL listing for 1-3/4″ thick doors only
• Available to accommodate lead in door thicknesses 1-3/4″ (44mm), 2″ (51mm), 2-1/4″ (57mm), 2-1/2″ (64mm), or 3″ (76mm) – specify when ordering
• Additional thrust bearing for greater load capacity
• Doors up to 90″ (2286mm) in height should use one intermediate pivot. Each additional 30″ (762mm) of door height warrants another intermediate pivot
• For 20-minute label suffix “–20” to the part number
• Non-ferrous base material for top pivot
• 3/4″ (19mm) offset (measured from centerline of pivot to face of door)
• Door edges must be beveled in 1/8″ in 2″
• Furnished with wood and machine screws
• Extended spindles available in 1/2″ (13mm) increments up to 2″ (51mm) longer than standard
• Doors will swing 180°, trim permitting


Offset Hung Pivots Notes
diagram_offset
The pivot point is offset from the edge of the door by 3/4”.
This allows the door to swing out and around any door trim, much like when butt hinges are used.
When the door trim is especially thick you may special order pivots that are offset by 1-1/2” to provide extra clearance. Using the larger offset does place more stress on the pivot point so intermediate pivots are often used to help keep the door aligned.

Intermediate Pivots
Pivot sets ship with a top and bottom pivot in a set. In most applications, a 3rd pivot is placed between them called an intermediate pivot. The intermediate bears no weight and is designed to keep the door aligned to prevent warping. A standard door height of 7′ typically takes one intermediate and more intermediates are added for each additional 2′ of door height.
Note that intermediates are only available for offset hung models. Center hung models have no intermediates available.

Model Numbers
Rixson model numbers make no sense. Don’t try to figure them out.
For example, model 117 is an offset pivot who’s offset is 3/4”, but model 117-3/4 is not offset at all. It is a center hung model. So when you see ”3/4” within a model number don’t think it has any significance.
Rixson manufacturers high quality products that last a long time. They just were asleep at the wheel when it came time to assign model numbers to them.

General Pivot Notes
Pivot sets provide the best possible means of hanging a door. They are designed to work with the laws of physics to provide long-lasting performance and reliability.
The weight of the door is supported entirely by the bottom arm, which is directly connected to the pivot spindle. This hanging means provides several important advantages:
• Fasteners on the door and frame are in shear rather than tension (as with hinges) and are less likely to pull out overtime. This creates less stress on the frame assembly, prevents door sagging and allows the door to swing with less resistance from friction.
• A door supported in this manner relies on the strength of the floor to carry the weight, not the frame. This allows extremely heavy doors to be hung in an opening and allows door adjustment throughout the life of the building to compensate for settlement.


33822_33821_33820_finishes_pullknobs
product_image_1727