B-5806 Grab Bar

B-5806 Grab Bar


  • Return period: 30 days
  • Ships From: Bobrick with 2-3 day lead time
SKU: B-5806 Category:
  • Description
  • Additional information
  • Returns


Bobrick Grab Bar – 1-1/4” Diameter – Concealed Flange
Stainless steel grab bar with snap on flanges for concealed mounting.
Stainless steel is 18 gauge, type 304, satin finish.
NOTE: Bobrick no longer furnishes mounting hardware (screws) with their grab bars. You will have to furnish your own screws. We apologize for this but it is a manufacturing decision that we cannot correct.


Grab Bar — 18-8 S, type-304, 18-gauge (1.2mm) stainless steel tubing with satin finish. 1-1/4″ (32mm) outside diameter. Ends are heliarc welded to concealed mounting flanges. Clearance between the grab bar and wall is 1-1/2″ (38mm).

Concealed Mounting Flanges — 18-8 S, type-304, 1/8″ (3mm) thick, stainless steel plate; end flanges 2″ x 3-1/8″ (50 x 80mm) with two holes for
attachment to wall. Intermediate flanges 2-5/8″ x 3-1/8″ (65 x 80mm) wide x 3-1/8″ (80mm) diameter. Snap Flange Covers — 18-8 S, type-304, 22-gauge (0.8mm) drawn stainless steel with satin finish. 3-1/4″ (85mm) diameter x 5/8″ (16mm) deep. Each cover snaps over mounting flange to conceal mounting screws.


Bobrick grab bars that provide 1-1/2″ (38mm) clearance from wall can support loads in excess of 900 pounds (408kg) if properly installed. Other grab bar configurations can support loads in excess of 250 pounds (113kg) if properly installed, complying with barrier-free accessibility guidelines (including ADAAG in the U.S.A.) for structural strength.

Warning: Grab bars are no stronger than the anchors or walls to which they are attached and, therefore, must be firmly secured in order to support the loads for which they are intended.


Provide concealed anchor device or backing as specified or required in accordance with local building codes before wall is finished. Fasten concealed mounting flanges to anchor device or backing with two screws in each flange. Snap flange covers over each mounting flange to conceal mounting screws. Concealed anchor devices and mounting screws are not included with Bobrick grab bars and must be specified as an accessory.
For Grab Bars with an Intermediate Flange(s), Pull Snap-Flange Covers away from mounting flanges. Place grab bar in desired mounting location. Use intermediate flange as a template to mark location of mounting screws at intermediate flange only. Mark screw locations at the center of the slot in the middle of the double-keyhole shaped mounting holes (2) in the intermediate flange. Remove grab bar from wall. Drive the intermediate flange mounting screws into wall at marked locations. Note: Make sure to leave a space of just over 1/8” (3.17mm) between the underside of the screw head and the wall. Install grab bar on the wall by placing the round ends of the intermediate flange double-keyhole shaped mounting holes over the mounting screws (2) are located in the middle of the flange slots. Install the mounting screws into the wall at the end flanges and secure tightly. Tighten the mounting screws at the intermediate flange. Press all snap-flange covers into place to conceal mounting flanges.

Note: Recommend use of 1/4” or #14 (M6.3) sheet metal or wood screws to install Intermediate Flange. #12 (M5.5) screws may also be used.


Grab bar shall be type-304 stainless steel with satin finish. Grab bar shall have 18-gauge (1.2mm) wall thickness and 1-1/4″ (32mm) outside diameter. Clearance between the grab bar and wall shall be 1-1/2″ (38mm). Concealed mounting flanges shall be 1/8″ (3mm) thick stainless steel plate, 2″ x 3-1/8″ (50 x 80mm), and equipped with two screw holes for attachment to wall. Flange covers shall be 22-gauge (0.8mm) stainless steel, 3-1/4″ (85mm) diameter, and shall snap over mounting flanges to conceal mounting screws and/or WingIt fasteners. Ends of grab bar shall pass through concealed mounting flanges and be heliarc welded to form one structural unit. Grab bar shall comply with barrier-free accessibility guidelines (including ADAAG in the U.S.A.) for structural strength. Manufacturer’s service and parts manual shall be provided to the building owner/manager upon request.

Additional information

Weight 10 lbs
Dimensions 48 × 3 × 3 in


30 Day Return Policy
25% Restock Fee