- Additional information
Bobrick B-7120 115V TrimDry™ ADA Surface-Mounted Hand Dryer – White
Durable, 22-gauge, zinc-plated steel with white epoxy cover with black plastic trim, automatic operation, dual air outlets.
115V AC, 15 Amp, 50/60 Hz, 1725 Watts, Single Phase, cULus Listed.
Cover — 22-gauge galvanized steel with exposed surface type-304 stainless steel with #4 satin-finish vertical grain (B-7128) or
22-gauge mild steel zinc plated with high-gloss white epoxy paint finish (B-7120) covers with UL 94-5VA black plastic trim and
side panels. Cover equipped with uniquely designed dual air outlets. Air-inlet is equipped with vandal-resistant grille. Cover
projects no more than 4″ (100mm) from wall and is secured to mounting base with two vandal-resistant, recessed hex screws.
Mounting Base — 20-gauge (1.5mm) plated steel with four 0.236” (6mm) diameter mounting holes.
Motor — Universal, 1/7 hp, 8000 rpm, on resilient mounting. Sealed ball bearing at drive-shaft end and self-lubricating sleeve
bearing at nondrive end. Equipped with automatic thermal-overload switch.
Fans — Two balanced, double-inlet centrifugal fans are mounted on motor shaft; directs airflow over heating element at 71 cfm.
Heating Element — Two coiled nickel-chrome heating elements are mounted in mica frame and protected by automatic
thermal-overload switches. Heating elements, heat air without hot spots — inaccessible to vandals.
Electronic Control — Infrared sensor automatically turns dryer on when hands are held under air-outlet opening and across
path of sensor. Remove hands from path of sensor and dryer stops. Electronic sensor has automatic shutoff approximately
1-1/2 minutes after dryer turns on if an inanimate object is placed across air-outlet opening. After inanimate object is removed,
electronic sensor automatically resets itself and dryer operates normally.
No-touch operation: electronic sensor automatically turns dryer on when hands are held under air-outlet opening and across
path of sensor. Dual air outlets provide a swirling circulation of airflow for comfortable hand drying. Drying time less than
25 seconds. Remove hands from path of sensor and dryer stops. Dryer operates only when actually drying hands, which
saves energy and operating costs. Electronic sensor will automatically shut dryer off 1-1/2 minutes after dryer turns on if an
inanimate object, such as tape or chewing gum, is placed across air-outlet opening. After inanimate object is removed, electronic
sensor automatically resets itself and dryer operates normally.
10-Year Limited Warranty — In addition to Bobrick’s one-year guarantee, Bobrick extends a limited 10-year warranty from
the date of purchase on all parts for Model B-7120 and B-7128 hand dryer, except motor brushes, to the original owner of the
installed unit against defects in factory workmanship or material under normal use and service. Motor brushes are warranted
for three years from date of purchase. This warranty is limited to the repair or exchange of defective parts at the option of
Bobrick. See Installation Instruction Sheet, Form No. 712-69, for full details.
Wall preparation: Locate mounting base on wall using template provided. For brick, stone, and concrete walls drill four
0.315″ (8mm) holes to suit provided wall plugs 0.315″ (8mm) x 1-1/4″ (45mm) and screws # 10 (4.8mm) x 2″ (50mm) long.
See template for wall plug and screw installation details. For plaster or dry wall construction, provide concealed backing to
comply with local building codes and secure with four #10 (4.8) round-head sheet-metal screws or 3/16″ (5mm) toggle bolts
(not furnished). Provide electrical service from nearest distribution panel to dryer mounting base in conformance with local
1. For 115-Volt Dryers — Connect ground wire to ground terminal marked , the black or hot wire to terminal marked L1,
and neutral or white wire to terminal marked N.
2. For 208–240-Volt Dryers — Connect ground wire to ground terminal marked and the 208-240-volt wires to terminal
marked L1 and L2.
Notes: Electronic sensor in Automatic dryers will pick up movement within 6″ (150mm) of the air-outlet opening. Use caution
when choosing location for Automatic dryers in confined areas. Consider proximity to doorways and other traffic areas.
Bobrick automatic hand dryers should be installed at least 15″ (380mm) above any projection or horizontal surface which may
interfere with the operation of the automatic sensor.
For installation instructions that include step-by-step installation procedures and details of electrical service connections, see
Form No. 712-69, which is packed with each shipment. This form is also available in advance upon request.
Surface-mounted hand dryer shall have either 22-gauge galvanized steel with exposed surface type-304 stainless steel with
#4 satin-finish vertical grain (B-7128) or 22-gauge mild steel zinc plated with high-gloss white epoxy paint finish (B-7120)
covers with UL 94-5VA black plastic trim. Slim profile cover shall project no more than 4″ (100mm) from the finished face of
wall to comply with accessible design guidelines (including ADAAG in the U.S.A.). Unit shall be equipped with dual air outlets
that provide a swirling circulation of airflow for (less then 25 seconds) hand dry. Motor shall be 1/7 hp, universal type on
resilient mounting with sealed ball bearing at drive-shaft end and self-lubricating sleeve bearing at nondrive end; equipped with
automatic thermal-overload switch. Heating elements shall be located on outlet side of fan, shall heat air without hot spots, be
inaccessible to vandals, and protected by an automatic thermal-overload switch. Electronic sensor shall automatically turn dryer
on when hands are held under air-outlet opening and across path of sensor. Dryer shall turn off automatically when hands are
removed. Sensor shall automatically shut dryer off approximately 1-1/2 minutes after dryer turns on if an inanimate object is
placed across air-outlet opening. After inanimate object is removed, electronic sensor shall automatically reset itself and dryer
shall operate normally. Unit shall be cULus Listed, and/or VDE approved, CE marked. Unit shall comply with EU Directive
“Restriction of Hazardous Substance” (ROHS) requirements for non-use of certain hazardous substances in the production of
electronic products. Unit shall be protected by a limited 10 -year warranty on all parts except motor brushes. Motor brushes
shall be warranted for three years from date of purchase.
|Dimensions||15 × 15 × 5 in|
30 Day Return Policy
25% Restock Fee
B-7128 115V TrimDry™ ADA Surface-Mounted Hand Dryer – Stainless Steel0 out of 5
- Return period: 30 days
- Ships From: Bobrick with 2-3 day lead time